Aircel RTM-3000 - Cycling Refrigerated Dryer

The Aircel RTM Series (2,500 - 30,000 scfm) utilizes high efficiency compressors with defined loading and unloading capacities and a thermal mass medium for energy storage. The refrigeration system cools the thermal mass medium to a predetermined lower temperature. Once that temperature is reached, the system goes into standby mode until the temperature rises to another predetermined set point. Only then does the system come out of standby mode and once again cools the thermal mass medium. No energy is wasted when demand on the dryer is low. The RTM dryers are ideally suited when large air volumes need to be dried to a reliable and constant dew point.

• 38°F - 50°F Dew Point
• Ambient Air Temperature 35°F - 120°F
• Maximum Inlet Air Temperature 140°F
• Maximum Operating Pressure: 150 psig
• 1 Year Standard Limited Warranty

All Aircel dryers are designed to give our customers the best value available in the industry - reliable performance meeting industry standards while consuming the lowest amount of energy possible. An Aircel high-capacity air dryer will always pay for itself by reducing air distribution system costs, lengthening tool life, reducing maintenance downtime and system damage.

Dimensions & Specifications

If you have questions on how to properly select a compressed air dryer, contact our knowledgeable customer service toll-free: 866-650-1937 or send us an email request.

1 Capacity rated in accordance with CAGI ADF 100 @ 100 psig, 100°F inlet,100° ambient, and a PDP of 38°F 2 Capacity rated in accordance with ISO 7183 @ 7 bar (101.5 psig), 35°C (95°F) inlet, 25°C (77°F) ambient and a PDP of 3°C (37.4°F)
† Run Load Amps (RLA); Mimimum Circuit Capacity (MCC)
RTM-2500 thru RTM-6000 stainless steel plate and frame heat exchanger standard
RTM-7000 thru RTM-30000 shell and tube heat exchanger standard

How the RTM Series Works

1. Hot saturated air from the aftercooler enters the air/air heat exchanger, where the air is pre-cooled by the cold dry air leaving the heat exchanger.

2. The pre-cooled air then enters the air/glycol heat exchanger, where is it cooled to its final dew point by chilled water/glycol, flowing in the counter-current through the shell.

3. The chilled air passes through the moisture separator, which has a high efficiency of separation at varying flow rates. Condensate is removed from the system without any loss of air via a zero purge drain valve.

4. Finally the cold, dry air is reheated in the air/air heat exchanger by the incoming hot air for maximum volumetric efficiency before exiting the dryer. The water/glycol is chilled by a cycling refrigeration system, and continuously pumped through the shell side of the air/glycol heat exchanger. The glycol flow rate remains constant, regardless of compressed air load. The refrigeration compressor unloads, and/or cycles OFF, when a pre-set water/glycol temperature is reached, thus minimizing electrical power consumption.

Standard Features

• Condenser automatic water regulating valve
• Inlet temperature indicator
• Outlet temperature indicator
• Refrigeration discharge pressure gauge
• Refrigeration suction pressure gauge
• Compressor sequencer (for units with multiple compressors)
• Compressor ON/light indicator
• Air inlet pressure gauge
• Air inlet temperature gauge
• NEMA 12 electrical
• Zero-purge drain system
• Pump pressure gauge
• Thermal storage temperature gauge
• Phase protection module
• High-temperature module
• Pump failure indicator
• No flow indicator
• Compressor starter with overload protection

Equipment Options

• Duplex pumps
• Multiplex compressor
• Air-cooled condenser
• Remote condenser
• Compressor sequencer
• Three-valve by-pass
• Mounted pre- and afterfilter
• Digital dew point monitor
• NEMA 4, 7

Compressor

As an industry leader in compressed air drying technology, Aircel uses high efficiency scroll compressors, semi-hermetic compressors, and rotary screws for all high-capacity dryers providing extra reliability and more energy savings.

Heat Exchangers

Aircel's high thermal efficiency stainless steel plant heat exchanger and ASME-stamped shell and tubetype pre-cooler/reheater and air-to-water/glycol heat exchangers are designed for low pressure drop and maximum performance.

Separator

High efficiency centrifugal separators and integrated stainless steel separators eliminate moisture from the air system. The unique design of the separator removes 99% of the water droplets with no mechanical movement and maintenance.

Condensers

Aircel's high-capacity dryers are built standard with air-cooled (2500-5000 scfm) or water-cooled (6000 and up scfm) condenser and automatic water regulating valve (remote air-cooled condenser option).

Demand-Activated, Zero-Purge Condensate Drain

One of the important components of the dryer is the discharge of the condensate, which has been removed from the compressed air supply. Aircel's zero-purge drain system automatically discharges contaminated condensate from compressed air systems.

Centrifugal Pump

High efficiency close-coupled centrifugal pump with back flow preventer and no flow shutdown provides reliable performance.

Allen-Bradley PCL Controller

• PLC controller with panel view (300 standard)
• Energy saving indication
• Dryer status text display
• Adjustable cycle time
• Refrigeration compressor loading/unloading indicator
• Compressor run indicator / Compressor off indicator
• Compressor sequencer (for multiplex option)
• Pump sequencer (for multiplex option
• Alarm indicator
• Common alarm dry contact for customer remote
• Communication port (option)
• Temperature indicator for refrigeration suction, discharge, evaporator, and water/glycol
• Dryer hour meter indication
• Energy saving hour meter indication

Aircel RTM High-Capacity Cycling Refrigerated Air Dryer Series

Brochure (pdf)

Contact our customer service team by calling toll-free 866-650-1937 or email sales@ecompressedair.com for more information about the RTM dryer or for customized options and quotes.